Shoe Factory Equipment: What do I need to make shoes?
What machines are needed to manufacture sneakers?
What shoe factory equipment do I needto open a real shoe factory?I’m going to walk you through a mass production shoe factory and detail all the shoe factory equipment you will need todo it right. If you are looking for hand tools for shoemaking click here.
I’m going to show you what you need to make a standard die-cut cold cemented sneaker. This is a simple shoe made with only die-cut parts. The outsole is a one-piece rubber cupsole with a die-cut midsole inside andchannel stitching.
First, modern shoe manufacturing relies heavily on sub-contracted factories for many specialized operations. For example, the shoe factory technicians developed the outsole designs, but the outsole tooling is produced elsewhere, with the rubber parts also purchased somewhere else from a company that specializes inrubber pressing. The shoe factory then controls the components to ensure the uppers and outsoles all fit together correctly.
Shoe Material Cutting and Marking
Inside the shoe factory, the first operations in the manufacturing process are the cutting and marking operations. The factory uses cutting presses, also called clicker cutting machines. The clicker press is one of the standard pieces you will see in every shoe factory, and they require cutting dies for each shoe pattern part.
New technology for cutting is the computer-controlled drag knife cutter. These machines use a vacuum table to hold materials in place while the blade cuts all the pattern parts. This technology is critical for custom mass production. Once the shoe parts are cut they get processed, with alignment marks screen printed onthe parts and any logos added. Logos can be silkscreen printed, radio frequency welded or embroidered onthe cut parts.
Footwear logo application
After the shoe parts are cut and marked for assembly, they may need to have logos added. Logos are added by silk screen printings, embroidery, or heat welding.
Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
Footwear upper stitching
The sewing machines come in many types: post, long arm, short arm, etc. The stitching line will have hundreds of these machines, the amount depending on the complexity of the shoe design. The style of the machine will also change to fit the specific operations required to make each shoe design.
Oncethe stitching is finished, it is time to set theshape of the toe box and heel counters. These machines heat the thermoplastic counters inside the toe and heel, then clamp the shoe to set the shape.
With the upper almost complete, we will need a special sewing machine to finish it. The Strobel sewing machine was invented by a guy named…you guessed it… Strobel! This machine is used to sew the bottom fabric onto the upper, closing it. The fabric bottom or “sock” is marked with alignment lines to ensure the upper is straight and not twisted. Now the upper is ready for lasting and assembly.
Shoe assembly process
With the shoe ready for assembly, it’s time to bring out the heavy equipment. The basic assembly line is about 100 yards long. On the front of the line, you will find a steamer to soften the shoe uppers, preparing them for lasting. The lasting machines are used to get the uppers pulled down tight ontothe shoe lasts.
The toe-lasting machine is the centerpiece of the lasting equipment. This machine takes hold of the upper and physically pulls it down around the last. The machine simultaneously pulls the upper into place while injecting hot glue to fix the uppers intoplace on the last. Once the toe lasting is complete, the waist and heel of the shoe may also be pulled into place by either hand operation or machine processes. Following the lasting operations, the lasted upper is placed into the first of the tunnels on the line. These tunnels are cooling tunnels that shrink the upper down to adhere to the last even tighter.
Footwear Primer and Cement
Now the lasted uppers and outsoles are on the conveyor line together, each receiving two coats each of primer andcement. After each application, the parts are placed back on the line to travel through a heat tunnel to dry the parts.
Once the parts are fully primed and covered with cement itis time to join the parts together. A worker takes the upper and sole in hand, fitting them together. Once the parts are fit, a pressing operation ensures the bonding surfaces are completely in contact.
Outsole pressing
The pressing operation compresses the bottom, sides, and heel of the sole and upper together. To set the bond, the lasted upper with the bottom attached is often placed in a chiller unit. Once out of the chiller unit, the shoe is de-lasted by hand or by machine. Depending on the design of the shoe, there may be just a few operations left. A possible process is for a shoe to receive channel stitching from a special oversized sewing machine that can stitch through the rubber outsole and the entire upper.
Finally, the shoe may pass through a dryer oven and UV light tunnel to ensure there is no possibility of mold growth while the shoe is in transit.
PrevPreviousNike Air Max 90: Counterfeit vs. Real
NextShoe PatternsNext
As an expert in shoe manufacturing, I bring extensive knowledge and firsthand experience to guide you through the intricate process of setting up a shoe factory. My expertise spans various aspects, from the initial design and cutting phases to the intricate assembly and finishing processes.
In the realm of modern shoe manufacturing, collaboration with subcontracted factories is a common practice for specialized operations. Now, let's delve into the key concepts discussed in the article about shoe factory equipment:
-
Shoe Material Cutting and Marking:
- Cutting presses, also known as clicker cutting machines, are fundamental in the manufacturing process.
- Computer-controlled drag knife cutters, a cutting-edge technology, use a vacuum table for precision and efficiency.
- Alignment marks and logos are added to cut parts through methods like silk screen printing, embroidery, or heat welding.
-
Footwear Logo Application:
- Logos are applied to shoe parts using techniques such as silk screen printing, embroidery, or heat welding.
-
Footwear Upper Stitching:
- Sewing machines come in various types (post, long arm, short arm) and are employed based on the complexity of the shoe design.
- Hundreds of stitching machines may be utilized on a stitching line.
- Machines for shaping the toe box and heel counters are crucial for setting the shape of the upper.
-
Strobel Sewing Machine:
- The Strobel sewing machine is used to sew the bottom fabric onto the upper, closing it securely.
- Alignment lines on the fabric bottom ensure the upper is straight and not twisted.
-
Shoe Assembly Process:
- A steamer is used to soften shoe uppers, preparing them for lasting on a 100-yard assembly line.
- Lasting machines pull the uppers tight onto shoe lasts, with a focus on the toe-lasting machine for precise shaping.
- Cooling tunnels shrink the upper to adhere tightly to the last.
-
Footwear Primer and Cement:
- Lasted uppers and outsoles receive primer and cement coatings through a conveyor line.
- Heat tunnels dry the parts after each application, preparing them for the bonding process.
-
Outsole Pressing:
- The pressing operation compresses the sole and upper together.
- A chiller unit may be used to set the bond before de-lasting the shoe.
-
Final Processes:
- Channel stitching from a special oversized sewing machine may be applied to the sole and upper.
- The shoe may pass through a dryer oven and UV light tunnel to prevent mold growth during transit.
This comprehensive overview should provide valuable insights for anyone considering venturing into the intricate world of shoe manufacturing.
